Hardware to Hang Curtains From Ceiling

Download Article

Download Article

Hanging curtains from the ceiling may seem daunting, but it has many benefits. For instance, the actress height it adds can make your ceilings look higher. Using the ceiling too makes it piece of cake to divide rooms or create little nooks in your dwelling house. A simple way to install curtains is to use brackets and a rod, much like you would when you hang curtains on the wall. You can also use a rail organisation with loops along with a curtain that has minor hooks, which works especially well for a wide drape.

1. 1

   Find rod brackets specifically fabricated for the ceiling. Brackets meant for the wall will accept a shallower "claw," which may not work for the ceiling. You can detect ones specifically for the ceiling online or in nigh home improvement stores.

   • When looking for a rod, cull one that'southward 8 to x inches (20 to 25 cm) wider than your window.^[1]
   • Also, pick upward some hollow wall anchors (molly bolts) if your brackets don't come with them and you have plaster ceilings; they should be the same size equally the screws that come up with your kit. Screws piece of work fine if y'all're going into wood, just with plaster, you need to anchor the holes with something sturdier. If you lot're non sure what to get, enquire for help at the domicile comeback shop. Bring in your brackets so they can run into them.
   • If you're using anchors, make certain they're made to support the weight you're hanging up. Anchors come in dissimilar weight ratings.^[2]

2. ii

   Measure and mark where you desire the brackets to exist. The brackets should come out ii to three inches (5.1 to 7.6 cm) from the wall so the defunction aren't right confronting the window. So, you should identify the brackets either right at the outer edges of the window or 2 to 3 inches (5.1 to 7.six cm) past the ends of the window on either side. Mark where the brackets should go with a pencil.^[3]

   • Keep in mind, you lot're aiming for the curtain rod to extend 4 to 5 inches (x to 13 cm) on either side. However, the stop decoration may affect how far y'all desire the brackets out from the window. If the decorations are wide, you may want to identify the brackets closer to the width of the window so that at that place's room for the caps to extend past the brackets.
   • Ever agree the rod upwardly to your marks to see if it looks right.
   • If you lot're going to be doing several windows of the same size, try making a template out of cardboard. Mark where the edges of the windows are and where you should drill the holes on the cardboard. And then you can utilize information technology to easily figure out where to drill above each window.

   Advertizement

3. 3

   Drill a airplane pilot hole that's the width of the hollow wall anchors you lot'll use. If your ceiling is plaster, you should use hollow wall anchors. Typically, you lot drill a pigsty that's the aforementioned size equally your anchors. So if the ballast is ¹⁄₈ inch (3.2 mm), use a drill bit that size. Press the scrap against the place you've marked. Turn the drill on and slowly press it into the ceiling, making sure y'all go all the mode through the plaster.^[4]

   • Drill a pigsty for each anchor you need to put in. You'll need an anchor for each pigsty in the bracket.
   • If you practise have woods ceilings, you tin simply screw in the brackets.
   • Always clothing protective goggles when drilling into the ceiling so aught gets into your eyes.^[5]

4. four

   Insert the hollow wall anchor into the holes and spiral it to the correct. Press the ballast in with your mitt until the teeth on the back take hold of in the plaster. Employ a screwdriver or drill to plough the screw to the right. Just the spiral should turn, not the anchor. This volition tighten up the anchor behind the screw. When information technology feels tight, you tin take the spiral out of the anchor.^[6]

   • To take the spiral out, turn it to the left with a screwdriver or drill.
   • Echo this process with all the anchors.
   • You should have a "reverse" push on your drill to make information technology go to the left as needed.

5. five

   Place the bracket over the anchors and screw it into place. Hold the subclass confronting the ceiling. Fix a screw into one of the holes, turning it lightly into the anchor below. Place the tip of the drill at the head of the screw, plumbing fixtures information technology into place. Turn the drill on slowly and let it rotate the screw into identify by turning it to the right.^[7]

   • You lot may want to have someone else concur the bracket while you use the drill.
   • Make sure the brackets are going the direction you want to hold the rod properly.

6. half dozen

   Put the curtain on the rod and hang information technology in identify. Slide the curtain over the rod. If you're using the kind with eye holes, alternating going front to back and back to front so that it pleats the curtain and hangs properly. Screw the finish caps on and hang the rod in place by setting it onto the hooks, centering information technology between the brackets.^[8]

   • To hibernate the bracket, make sure you slide the rod into the front end of the pall (and out the back) start when putting it on, and then through the back and out the forepart. That will create a concave consequence that y'all tin slide around the bracket to hide it.
   • In some cases, you may demand to put the rod in place before yous screw the end caps back on.

7. 7

   Tighten the screws over the rod if yours has them. If you had to remove the end caps to slide the curtain into place, and so your brackets likely have screws that assistance hold the rod. Merely use a screwdriver or drill to tighten them, which volition help keep the rod from moving around.^[9]

   Advertizement

1. one

   Find a rail subclass specifically for the ceiling. These brackets are a long piece of metal with tiny loops in them for hanging curtains. Opt for ane that's eight to x inches (20 to 25 cm) wider than your window, allowing the mantle to aggrandize past the edges. You can detect these online or at most habitation comeback stores.^[10]

   • If you accept plaster ceilings, you lot'll also need hollow wall anchors (molly bolts) if your kit doesn't come up with them. Option ones that are the same size as the holes in the brackets. These help anchor the screws into the ceiling. If y'all accept a wood ceiling, merely screws are fine.

2. 2

   Add the braces to the brackets as needed. Some kits come with little braces that you snap into place on the back of the rails. Your kit should tell you how to install them, just typically, you only slide them over i border of the track and pull it toward the other side. And so, yous snap it into place by pressing down.^[11]

   • Some brackets take little "arms" you'll need to pull open then you can put information technology in place and close the arms.
   • Spread the brackets out evenly along the rails. They can move back and forth.

3. 3

   Mensurate where the anchors will go and place a dot at each 1. Hold a tape measure up and mark a spot two to 3 inches (v.i to 7.vi cm) from the wall, depending on how far out y'all want your curtains. Hold the track upwards at this spot. Centre it above the window, using a tape mensurate as needed to help you notice the middle. Once you take the rails where you want information technology, mark where each of the anchors needs to go with a pencil.^[12]

   • If yous're having trouble holding the runway in identify and mark at the same time, apply painter's tape to temporarily attach it to the ceiling. Take the rails downward again before drilling the pilot holes.

4. 4

   Drill pilot holes for the wall anchors. The pilot holes should be the same size equally the anchors. Therefore, if you take a ¹⁄_eight  in (0.32 cm) anchor, you demand a drill bit of the same size. Identify the drill against the ceiling, making certain information technology's perfectly perpendicular. Then, plough the drill on slowly. Let it do the piece of work of drilling the pigsty as you employ gentle pressure.^[xiii]

   • Make a hole for each place y'all've marked.
   • Vesture rubber glasses while you drill to protect your eyes.^[14]

5. 5

   Printing and screw each anchor into place. Push the anchor into the plaster with your fingers. The teeth on the anchor should take hold of. Then, use a Phillips head screwdriver or screwdriver bit for your drill to plough the screw to the right. The anchor should be held in identify by the teeth. Every bit the drill turns, the metallic pieces behind the anchor volition tighten up. When it feels tight, yous can stop and pull the screw out.^[fifteen]

   • Turn the spiral to the left to pull information technology out. You tin use the screwdriver or a drill bit, but make sure to reverse the drill to pull information technology out. About drills have a "reverse" button.
   • Repeat the process for all the holes.

6. 6

   Screw the runway into place. Hold the rails up confronting the anchors. Begin at 1 cease, and put the screw through the track'south braces to the anchor below. Use your fingers to spiral it in a footling until it catches, and so place the tip of the drill against the tip. Turn the drill on slowly to screw it into identify.^[16]

   • Echo the procedure with each screw until you've done them all and the rails is held in place.

7. 7

   Insert the drape hooks into the loops on the rails. Y'all should have loops all along the lesser of the rail. Kickoff at i end, and grab a hook on one end of the curtain. Put one hook in each loop yous encounter. Make sure not to skip any, as that will leave gaps in your curtains. When y'all've reached the last loop and hook, you're done.^[17]

   • If your curtain doesn't have the hooks, you lot can insert them in place at the peak of the pall on the back. The holes should be marked, and you just slip information technology underneath the bottom edge of the hem and out through the top.^[18]
   • You tin as well install pull wands in the centre of the track but by hooking them into place over the loops.

   Advertisement

Enquire a Question

200 characters left

Include your e-mail accost to go a bulletin when this question is answered.

Submit

Advertizement

• Always be safe when using ladders! Take someone agree the bottom to help go along information technology steady.

Advertisement

Things You'll Need

• Measuring tape
• Pencil
• Brackets and a rod for the ceiling
• Hollow wall anchors (molly bolts) or screws
• Drill $.25 and drill
• Pall

• Measuring tape
• Pencil
• Track bracket meant for the ceiling
• Hollow wall anchors (molly bolts) or screws
• Drill $.25 and drill
• Drapery with pocket-sized hooks

Nearly This Commodity

Thanks to all authors for creating a folio that has been read 32,513 times.

Did this article aid yous?

Share this post